Restaurant chairs and tables, chosen togetherFor restaurants and hospitality rooms. Tables and chairs are ordered 8 pieces or more, mixed as you like.Talk to a specialist

The room journal

Restaurant chair arm clearance under table aprons

In this guide

An armchair can look as if it belongs under a dining table until somebody sits down. A front arm meets a lip below the tabletop. The guest backs out a few inches to find a usable position. At a wall seat, that small move may put the chair back exactly where the server was about to pass.

Restaurant chair arm clearance under table aprons starts with the smallest vertical opening the arm has to travel through. Measure from the same floor to the highest part of the arm that enters the table and to the lowest part of the top assembly along that route. Try the movement with a person in the chair. A plan drawn from the overall table height alone leaves out the contact point.

Side profiles of a 30-inch tabletop and 26-inch apron. A 25-inch chair arm clears by 1 inch; a 27-inch arm overlaps by 1 inch.
Illustrative side sections using the same 30-inch tabletop and 26-inch apron underside. Measure the highest point of the chair arm where it passes the apron.
Open diagram at full size (new tab) ↗
Read the diagram in text

Two illustrative side sections have a tabletop 30 inches above the finished floor and an apron underside at 26 inches. Chair A has a 25-inch arm and clears the apron by one inch. Chair B has a 27-inch arm and overlaps the apron height by one inch. Chair and table shapes are schematic.

  • FURNITURE CENTRAL
  • Measure the lowest edge the arm must pass beneath.
  • Chair A
  • 1 in clear
  • Finished floor
  • 25 in arm height
  • Chair B
  • 1 in overlap
  • Finished floor
  • 27 in arm height
  • Worked example. The tabletop is 30 in high. The apron underside is 26 in.

Draw the underside as well as the top

Look under the actual table before opening the chair shortlist. Mark its top edge, any apron, an underframe, and any brace near the chair approach. Take the measurement at the entry and again where the arm would sit when the guest is settled. A band under a top can change depth at a corner or joint. Make a separate note if only part of the edge has a clear opening.

Use the restaurant table system guide to record the top and base together. Two finished tables can look alike while presenting different openings at the underside. Keep the drawing attached to the exact table configuration or the table number for a retained piece. If you compare a cantilever base with another base, note where its supporting structure sits in relation to the entry. The base's shape belongs on the same sketch.

Check the highest part that actually goes under

Set the candidate on the floor beside the table with its front facing the intended position. Measure to the top of the arms at the front, middle, and rear. Slide the empty chair partway in and mark the furthest point each arm would reach in ordinary service. Have a coworker sit down and repeat the approach. A profile that rises toward the back can stop at an unexpected place.

Suppose the tabletop is 30 inches from the floor in a measured sample setup. The lower edge of the apron is 26 inches from the floor. The arm of Chair A measures 25 inches at the highest point that enters the opening, while Chair B reaches 27 inches at the same point in its travel. The first leaves 1 inch at the apron in this measured setup. The second meets the apron 1 inch too high even though both arms sit below the visible tabletop.

One inch on a tape is a starting point for a real test. Put the chairs at the table with the napkin and place setting in position. Check whether a seated guest can move closer, leave easily, and turn toward an open aisle. For more choices to trial, use the armchair selection and the comparison of armchairs and side chairs.

Try the tightest table position first

Move the sample table to the wall position in the room where space is tightest. Set a second chair at the neighboring table. Ask one person to stay seated while the other approaches and takes the wall seat. Watch what happens when the occupied chair can travel only to the point the arm stops. The usable aisle is the opening you have while the room is in service.

Consider a measured test with 39 inches between the edge of the table and a nearby obstruction. At one position the chair projects 19 inches into that gap while occupied, leaving 20 inches. At another position the arm stops the chair 4 inches farther out. The opening becomes 16 inches. Those numbers describe that mockup. Bring your own room requirements and verify the final layout before approving the furniture.

Try a side chair from the dining range at that same position. Compare its approach and how the table looks from the rest of the room. A consistent palette can include two seat shapes where the dimensions call for them. Look at the shortlist of dining tables if the chair is the piece the design has to retain.

Test the whole place setting

Leave the sample chair in place and carry a tray to the table. Reach for the glass at the far setting. Notice whether you can set a plate down without asking the guest to move. Check what happens when two tops are joined and their undersides meet at a slightly different position. If the arrangement changes for reservations, record clearance with both layouts.

Compare the underside of a complete table configuration with a top and its separately selected base. A support or mounting part can project below the edge even where the table has no apron. Use the exact current drawings or a physical sample for the actual choice. If a listing gives a tabletop height and leaves the apron measurement unanswered, take it from the sample or request the dimension for the specific configuration.

If the chairs will be shared by two kinds of tables, keep both tables in the trial. Mark the measurements separately on the same card, then draw an arrow from each number to the exact point it describes. A buyer returning to the room should be able to repeat the measurement without taking the chair apart.

The finish comes back into the decision after the fit check. Put the chair beside the top in the room's light. Request material samples when the same chair has more than one relevant seat or frame finish. Keep the successful dimensions with the sample details.

Keep the point of contact on the board

Draw the limiting edge on the measured sketch. Save the successful chair and table selections on the finish board and use the same reference in its notes. Record the highest entering point of the arm, the lowest point of the opening, and the occupied chair position. Add a photograph from the side so a second buyer can see exactly where the measurements belong.

Review the ordering steps with the approved combination beside you. Give a retained table its own label when it differs from the new ones. The next person adjusting the dining layout can bring the same chair to the marked table, sit down, and tell immediately whether the pairing still works.

Browse furniture

Furniture in this guide

Bring these pieces into your room plan

Open a product to check its current options and listed price. Review the selected size and finish before adding it to your plan.